FRP Wind Ventilators

FRP Wind Ventilators
 

We are manufacturing FRP Based Wind Ventilators, which are hugely admired by clients in the domestic as well as international markets. Assembled as per the latest industry standards.  
Our FRP Based Turbo Air Ventilators are manufactured using Owen Roving Mat, Surface Mat, G.P. Resin, Catalyst and Escalator to match the designing of the roof. Features of this ventilators are Minimal erection and structural cost due to its light weight, Well-protected from corrosion, rust and warping

Easy to install and maintenance.
 
TECHNICAL DATA FOR
FRP MUKTA WIND VENTILATOR
 
 

Sr. No.

Particulars

 

Specification for FAN Mukta Wind Ventilator 600mm Throat Dia.

1)

Vanes

Vanes made out of FRP (Glass Fibre Reinforced Plastic)  UV Stabilized Isopthalic Resin . No. of Vanes: 42 nos.
Thickness of vanes: 2mm (+/-0.2mm)

2)

Top Plate

Top Plate made out of FRP(Glass Fibre Reinforced Plastic)  UV Stabilized Isopthalic Resin .Dia. Of Top Plate: 500mm (+/-5mm)
Thickness of Top Plate: 2mm (+/-0.2mm)

3)

Bottom Ring

Bottom Ring made out of FRP(Glass Fibre Reinforced Plastic)  UV Stabilized Isopthalic Resin.Dia. Of Bottom Ring: 600mm (+/-5mm) Thickness of Bottom Ring: 2mm (+/-0.2mm)

4)

Fan Spoke Assembly

Fan Spoke assembly made out of SS 316 L Rod. Dia. of Fan Spoke Rod: 5mm.

5)

Bottom Ring Cross Bracket

Bottom Ring Cross Bracket made out of SS 316 L Flat.
Size of Cross Bracket Flat: 18 X 3mm

6)

Shaft

Shaft made out of SS316 L Rod 12 mm Dia.

7)

Shaft Casing

Shaft Casing made out of (UV Stabilised) U-PVC pipe, 32mm Dia.(min), 2 mm Thk (min.)

8)

Shaft Bottom Cap

Shaft Bottom Cap made out of Polypropylene ( PP ), Internal Dia- 34mm, Outer Dia-36mm,
 1mm Thk.

9)

Bearing

2 nos. Permanently sealed & lubricated Bearing of Type 6001 ZZ.

10)

Rivet

SS 304

 

Specification for BASE PLATE for Mukta Wind Ventilator 600mm Throat Dia.

1)

FRP (Glass Fibre Reinforced Plastic)  UV Stabilized Isopthalic Resin . Translucent Type. Confirming to match existing roof sheet profile.
Size of Base Plate: 1.050 W X 1.6 L Mtrs.
Height of Throat: Higher side- 400mm; Lower side- 310mm
( +/- 5mm)
Top Dia of Throat: 590mm ( +/- 5mm)
Thickness of Base Plate: 2mm (+/- 0.3 mm)

 
 
Address :

Registered & Correspondence Office
C-20, Neighbourhood Shopping Complex,  Mother Teresa Road, Sector 4, Nerul (W),  Navi Mumbai - 400706,
Maharashtra, India. Tel : (022) 27721271 / 27714027 / 32253608 , Fax : (022) 27714027

Factory : S.No. 27- 1-1A, Tathavade , Pune - 411033 , Tel : 020-27279912
Web :- | www.airventilators.net | www.muktawindventilators.com | www.econaturalventilators.com |
           | www.anantlaxman.com | www.turboventilators.com |